Autel IM508 Add Smart Remote on 2018 Honda Civic

Autel IM508 can be used on Honda Civic to add key, do all key lost, reset immobilizer, replace IMMO components (engine/immobilizer/for blade key), (smart IMMO box/for smart key) and read live data/DTC. This post will share how to add more smart remotes on a 2018 Honda Civic by keyless system.

 

Tools need:

Car: 2018 Honda Civic

One working key+ one new key (Smart key chip: 47 frequency 433Mhz)

Device: Autel MaxiIM IM508 key programmer

Autel IM508

Procedures:

Push Start

Test two keys, the original key works normally, and the new key cannot work.

Turn ignition ON (press button 2 times)

 

Then follow the step-by-step guide to operate, the instruction also appears on the screen to help you to operate easily.

 

Connect MaxiIM IM508 with the vehicle’s DLC by the cable’s 16-pin male adapter

Enter the MaxiIM tablet, select [Honda]-> [System Selection]-> [Keyless System]-> [Touch-tone smart card (Honda)]

Autel IM508

Check if the ignition is turned on by pressing Start button twice.

Then it will configure system automatically

Select [Registration]-> [Add Smart Key]

Autel IM508

Pay attention to the registration condition:

1.There is no DTCs.

2.There must be one registered keyless remote.

3.One keyless remote that is capable of starting the engine must be in the vehicle

4.The ignition switch must be turned on (II) using the keyless remote. (The ignition key must not be used).

Registration notice:

Ensure the following processes to reduce noise as much as possible during keyless remote registration:

-Turn off all electrical devices (e.g., navigation and audio systems)

-Separate the diagnostic tool from the keyless remote as much as possible

-Close all doors, windows and sunroofs

Turn the ignition switch off

Note: Don’t press the foot brake and press the engine start/stop button

Wait for the ECU to stabilise…

Take registered remote inside the car and all others outside

Autel IM508

Turn the ignition switch on

Checking vehicle condition…

Take all original keyless access remotes out of the vehicle (within 100 sec)

Take a new smart remote into the car

Autel IM508

Register the new smart remote successfully

Autel IM508

Turn the ignition switch off and then on

Check if both the keyless are access and immobilizer indicator lights are turned off

Autel IM508

Turn the ignition switch off and then on again

The registration is completed.

Turn the ignition switch off

Autel IM508

Finally, check all smart remotes can turn on

Autel IM508

Autel IM508

See also:

XHORSE KEY TOOL MAX PLUS AUTEL IM508 ADD SMART KEY TO NISSAN NOTE 2019

AUTEL IM608 WITH XP400 ADD BMW 320I 2013 KEY

AUTEL IM608 GENERATE SIMULATOR KEY FOR TOYOTA SIENTA 2016+ CAR LIST

  • Does the Maxisys MS905 Program New IMMOBILIZER on Chevy HHR ?

    Does the Maxisys MS905 Program New IMMOBILIZER on Chevy HHR ? Owner Question:  Hello we got a 2008 Chevy hhr towed in someone tried to steal the car and ripped the ignition switch and housing and immobilizer apart. We got a used steering column from the junk yard. I installed the new column. Did the 10 minute relearn now the car cranks and starts but won’t run. Does the new immobilizer have to be programmed to the body computer and the ECM. does the Autel MaxiSys Mini MS905 read and send the new fuel pass word to the BCM or ECM?   Tech […]

  • autel ms906 How To Register Autel Maxisys MS906 Diagnostic Scanner

    How To Register Autel Maxisys MS906 Diagnostic Scanner Original AUTEL MaxiSYS MS906 Auto Diagnostic Scanner is the updated Version of […]

  • Step to update Autel Md808 Pro Software

    Autel MD808 Pro software support update online lifetime for free, before you can update on autel official website, you need […]

  • Autel MaxiSys Pro MS908P Software Update Gudie (3) Autel MaxiSys Pro MS908P Software Update Gudie

    This article aims to guide on how to update software for Autel MaxiSys Pro. (Suitable for MaxiDiag Elite,MaxiCheck,TS501,TS601,AL609,AL619,EBS301,OLS301,VAG505, MOTPRO) Step […]