Autel Diagnosis / Key Prograrmming
Problem: When I was using Autel IM508S & Toyota 8A IKEY to generate 2022-2023 Toyota Corolla Cross remote, it failed with a prompt: “The key type is incorrect. Use general low-frequ universal key.” What’s the problem? Any ideas? Solution The Toyota 8A IKEY is only workable for 8A remote. Please change a Autel Universal Key to … Read more Fixed: Autel IM508S Toyota 8A IKEY “The Key Type Is Incorrect” Issue
Today we’re going to program 2023 Honda HR-V all keys lost with Autel MaxiIM KM100 by OBD. Let’s go ahead and get started. IMMO >> Honda >> Manual selection >> HR-V >> Smart Key >> Push to start >> Yes >> Hot function Is the ignition turned on by pressing Start button twice? No … Read more Autel KM100 Program 2023 Honda HR-V All Keys Lost Success
Problem: When I use Autel MaxiIM IM508S to add key on all Ford models and all years, it fails. And it just stays on loading and doesn’t go any further. It gives a message: ” Authorization check failed! Error code: 1″. What’s the problem? Any advices? Solution Go to Data Manager-> Uninstall Vehicle -> Delete The Vehicel, … Read more Fixed: Autel IM508S Authorization Check Failed! Error Code: 1 Issue
In this article, I’ll show how to program 2017-2020 Chevrolet Trax all smart keys lost with Autel KM100E by OBD. The operation include 2 steps: read pin code and program keys. Read PIN Code IMMO >> Chevrolet >> Manual selection >> USA >> Trax >> 2017-2020 >> Smart key >> Yes >> Hot function >> … Read more Autel KM100 Program 2017-2020 Chevrolet Trax All Keys Lost
In this article, we’re gonna use Autel IM608 II & GODIAG GT110 to test 2016-2023 VW VAG 4th dashboard by bench. Full Operation Video: Connect IM608 PRO2, GODIAG & Dashboard Module, turn ignition on. The dashboard indication means that the key is not recognized. The light of GODIAG Key Identifier flashes for a long … Read more Autel IM608 II + GODIGA GT110 Test 2016-2023 VAG 4th Dash
Problem: The Autel XP400 PRO always gave the tips when connecting to a computer: “Please disconnect the programmer P1 pin. Verify that the programmer p1 pin is completed! Comunication error of the programmer. Please click ‘OK’ to connect the programmer again!” What’s the p1 pin? Doesn’t XP400 PRO work alone? Please help. Solution … Read more Fixed: Autel XP400 Pro Verify Programmer P1 Pin Is Completed Error
Now we’re working on some Ford CER keys from two different manufactures. We’re going to use the Autel KM100 & AT100 Universal Transponder to see if we can clone these Ford keys. Let’s go ahead and get started. The 1st one is a standard 2005-2016 Ford key. Reading/Cloning >> Reading As we can see, it’s a … Read more Autel KM100 & AT100 Chips Clone Ford Keys Test Review
Today I’m gonna attempt to clone Toyota ID4D ID67+ 40bit key with Autel AT100 + KM100 Key Programmer. This is the first time I’m using the new chip, here we go. Put the original key into Autel KM100 key slot. Reading/Clone >> Reading We can see it’s a TIRIS DST 4D, ID67 chip. Clone … Read more Autel KM100 Clone Toyota ID4D ID67+ 40Bit Key with AT100 OK
Problem: The Chevrolet Tahoe 2005 5.3 Liter has a fault code B3031 “Security system control in learn mode” on Autel IM608 II. The car is running normally but the immobilizer light is on. What’s the matter? Please help. AutelShop.DE engineer replied The vehicle should still be in learning mode. Power off the vehicle for … Read more Autel IM608 Solution: B3031 Security System Controller In Learn Mode
Problem: Hello dear seller, today I was updating my Autel IM508S and now if I try to open any diagnostic or immo function shows this error in the screen: Your application does not support this feature. Please upgrade to a new version. dlopen failed: “/data/data/com.Autel.maxi/lib/libDiag.so” is 32-bit instead of 64 bit Solution Provide SN with … Read more Fixed: Autel IM508S “Your application does not support this feature”