How to disable TPMS with Porsche Piwis Cable

 How to disable TPMS with Porsche Piwis Cable

The following part displays the step-by-step guide of disabling TPMS with a Porsche Piwis cable on a 2008 Porsche Boxster S 987.

Tool needed:

1. Porsche Piwis cable (cheap $30- on aftermarket, like $20.99 in uobd2)
2. Screw driver
3. 11mm socket
4. A laptop/computer running win xp home

NOTE: This Piwis cable fits most of Porsche Models from year 1990 to 2007. But this cable does not support newer Porsche models.

Step 1: Disconnect the TPMS control unit

1) Disconnect the TPMS control unit locate to the right of the brake booster. Open front trunk and dislodge the weather stripping that seals the front trunk. Remove the entire seal loop from the trunk. (See the picture below)
Piwis cable
2) Remove the plastic cover that protect your DVD/brake booster. Remove following 7 screws circled in red picture below with a screw driver. Then remove the light and plastic carpet hold marked red arrow.
Piwis cable

3) You can see the TPMS control unit white box marked red in picture below which located next to the brake booster. Use the 11mm socket to remove the plastic nut market red arrow.
Piwis cable
4)  The connector has a swing arm connection. You simply need to first press down on the small catch tab (red circle), then lift the pink swing arm (see insert).
TPMS

Step 2: Recoding with Porsche Piwis cable

1) Turn the vehicle ignition switch to ON position
2) Turn on hazard signal
3) Plug the Porsche Piwis cable into the OBD port
4) Connect the cable with computer/laptop via USB port
5) Install and run software
6) Select “Instrument cluster”>> “Coding”>> “Tire Pressure Monitoring System (TPMS) Not Installed” and “Normal pressure display (TPM) Not Active” in the software Function list.
Don’t forget to back up files when you do some changes.
Piwis cable
7) Select “Commands”>> “Reset”>> “Send” to reset the instrument cluster node
Porsche Piwis cable
8) Select “Gateway”>> “Coding”>> “Tire pressure monitor Not installed”
Porsche Piwis cable
Exit the software program is the process is complete. Otherwise, continue to realize other functions.

 

Know More information about Autel TPMS or Porsche car diagnostic  tool

See my Autel blog in the website: www.autelscanner.org

 

  • Autel Maxisys Bluetooth Vehicle Communcation Interface (VCI)

    Autel Maxisys Bluetooth Vehicle Communcation Interface (VCI) Table of Contents   General Notice …………………………………………………….1 Introduction ………………………………………………………. 2 Functional Description ……………………………………….. […]

  • VAG Group Cars Pre-2011 Autel Service Reset

    Please see the service reset procedure below; Click on the VAG manufacturer, wither Audi, Seat or other and then, Please select Systems Please select Control unit Please selectelectronics 1 Please select Instruments Please select Adaption The diagnostic tool will now ask you for a channel number. Select channel 002. Ask to set a new value and change to 00000. Once done escape from adaption’s and then go back in again. Select channel 053. Ask to set a new value and change to Once done escape from adaption’s and then go back in again. Select channel 054. Ask to set a new value and change to 00000. Once this is done, escape out of adaptions and instruments, turn ignition off and remove key. Leave for 10 seconds – then turn the ignition back on and service message should have cleared.   More information: www.autel.uk   Who Viewed This Article Also Views: OBD2 Scanner Autoboss V30, Autel MaxiDAS DS708 Comparison […]

  • Compare Auro OtoSys IM100 and Auro OtoSys IM600 with Autel MX808IM

    Here share a comparison of Auro OtoSys IM100 vs Auro OtoSys IM600 vs Autel MX808IM. This blog will compare their IMMO, Programming, OE-Level […]

  • autel maxidiag elite md802- How to Update Autel MaxiDiag Elite from 4 System to Full System

    How to Update Autel MaxiDiag Elite from 4 System to Full System Generally, Autel MaxiDiag Elite Scanner has two models: MaxiDiag 4 system […]